Micronics PCI/ISA System Board D6-IN Guia do Utilizador descarregar pdf (Página 21)

Appendix A

Chips & Tech

(90)Set

up RAM.

Phoenix

(90)Initialize hard

disk controller.(Beep)=3

Error Code

–

AMI

(91)Floppy setup complete. Hard

disk setup to be done next.

Compaq

(91)CMOS seems to be OK.

Chips & Tech

(91)CPU speed.

Phoenix

(91)Initialize local

bus hard

disk controller.(Beep)=3

Error Code

–

AMI

(92)Hard disk setup complete. About to go for BIOS ROM data area check.

Compaq

(92)Error on CMOS read/write test.

Chips & Tech

(92)Configuration check.

Phoenix

(92)Jump to User Patch 2.(Beep)= 3

Error Code

–

AMI

(93)BIOS ROM data area check halfway. BIOS ROM data area check to be

completed.

Compaq

(93)Start of D

MA controller test.

Phoenix

(93)Build MPTABLE for multi processor boards.

Error Code

–

ACER

(94)#5 shutdown.

AMI

(94)Hard disk setup complete. Going to set base and extended memory size. BIOS

ROM data area check over.

Compaq

(94)Page registers see

m OK.

Chips & Tech

(94)POD Bootstrap.

Phoenix

(94)Disable A20 address line.(Beep)=3

Error Code

–

AMI

(95)Memory size adjusted due to mouse support, hard disk type

47.Going to verify

from display memory.

Compaq

(95)DMA controller OK.

Chips &

Tech

(95)Reset ICS.

Phoenix

(95)Install CD ROM for boot.

Error Code

–

AMI

(96)Memory size adjusted due to mouse support, hard disk type

47.Going to do any

Init before C800 optical ROM control. Returned after verifying from display

memory.

Compaq

(

96)8237 DMA Initialization complete.

Chips & Tech

(96)BIOS PEAK.

Phoenix

(96)Clear huge ES segment register.(Beep)=3

Error Code

–

AMI

(97)Any Init before C800 optional ROM control is over. Optional ROM check &

control will be done next.

Chi

ps & Tech

(97)VGA power.

Phoenix

(97)Fix

up Multi Processor table.

Error Code

–

ACER

(98)#A shutdown.

AMI

(98)Optional ROM control is done. About to give control to do any required

processing after optional ROM returns control.

Chips & Tech

(98)Ad

apters POS.

Phoenix

(98)Search for option ROMs. One long, two short beeps on checksum

failure.(Beep)=3

Error Code

–

AMI

(99)Any initialization required after optional ROM test over. Going to setup timer

data area and printer base address.

oenix

(99)Check for SMART Drive(optional).

Error Code

–

AMI

(9A)Return after setting timer and printer base address. Going to set the RS

232

base address.

Phoenix

(9A)Shadow option ROMS.(Beep)=3

Error Code

–

AMI

(9B)Returned after RS

2 base address. Going to de any initialization before

Processor test.

Error Code

–

ACER

(9C)#B shutdown.

AMI

(9C)Required initialization before co

Processor is over. Going to initialize the

CoProcessor next.

Phoenix

(9C)Set up Power Management.(

Beep)=3

Error Code

–

AMI

(9D)CoProcessor initialized. Going to do any initialization after CoProcessor test.

Error Code

–

AMI

(9E)Initialization after CoProcessor test is complete. Going to check expander

1 2 ... 16 17 18 19 20 21 22 23 24

Comentários a estes Manuais

Sem comentários

Micronics PCI/ISA System Board D6-IN Guia do Utilizador Página 21

Comentários a estes Manuais